NACE-CIP1-001 Updated Exam Dumps [2024] Practice Valid Exam Dumps Question
NACE-CIP1-001 Sample with Accurate & Updated Questions
NEW QUESTION # 45
In a non-convertible coating the role of the primary solvent is to:
- A. To control the evaporation rate
- B. To promote faster cure
- C. To make the coating flow out better
- D. To dissolve the resin
Answer: A
NEW QUESTION # 46
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Never change his/her mind
- B. Call the supervisor
- C. Achieve consensus through negotiation
- D. Go with the majority opinion
Answer: B
NEW QUESTION # 47
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Personal Protective Equipment
- C. Safety Enforcement
- D. Engineering Controls
Answer: A
NEW QUESTION # 48
The least effective method of surface cleaning is most likely
- A. hand tool cleaning.
- B. power tool cleaning.
- C. water blasting.
- D. dry grit blasting.
Answer: A
NEW QUESTION # 49
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. The inspection cost will be offset by an improvement in service life
- C. The Inspector will improve job flow and schedule
- D. a) and c)
Answer: D
NEW QUESTION # 50
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- B. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- D. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
Answer: C
NEW QUESTION # 51
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Review the relevant standard with the Contractor
- B. Call your supervisor
- C. Shut the job down
- D. Permit coating to take place so as not to lose the blast
Answer: A
NEW QUESTION # 52
Checking is
- A. an exposed area of the substrate or previous coat material, caused by poor application technique.
- B. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- C. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- D. a fine crack in the surface of a coating that rarely reaches the substrate
Answer: D
NEW QUESTION # 53
Stripe coats are generally applied to:
- A. a), b), and c)
- B. Complex geometric shapes
- C. Welds
- D. Edges and corners
Answer: A
NEW QUESTION # 54
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Conditions E-G
- B. Surface Condition H
- C. Rust Grades 1-4
- D. Rust Grades A-D
Answer: D
NEW QUESTION # 55
ISO SA 2.5 is defined as:
- A. Near White Metal Blasting
- B. Very Thorough Blast Cleaning
- C. Light Blast Cleaning
- D. Thorough Blast Cleaning
Answer: B
NEW QUESTION # 56
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 75 Gauge Readings resulting in 25 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
Answer: D
NEW QUESTION # 57
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. In the field only
- B. At all times
- C. In the office only
- D. Only if the specification requires it
Answer: B
NEW QUESTION # 58
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Atmospheric Corrosion
- B. General Corrosion
- C. Localized Corrosion
- D. Galvanic Corrosion
Answer: D
NEW QUESTION # 59
Check abrasive blast pressure with a
- A. nozzle aperature gauge
- B. surface comparator
- C. needle pressure gauge
- D. replica tape
Answer: C
NEW QUESTION # 60
SSPC SP 1 identifies the use of:
- A. Biodegradable detergents
- B. Inorganic solvents
- C. Organic solvents
- D. A wide variety of materials
Answer: D
NEW QUESTION # 61
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record your result by identifying two segments
- C. Record the segment with the less aggressive profile
- D. Record the segment with the more aggressive profile
Answer: C
NEW QUESTION # 62
The Inspector should record the serial numbers of inspection instruments:
- A. Each time the instrument is used
- B. Only if the instrument is suspected of not working properly
- C. Only when verifying accuracy of the instrument
- D. Only if the specification requires it
Answer: A
NEW QUESTION # 63
ASTM Standards are applicable:
- A. In North America
- B. When specified
- C. In Asia
- D. In the USA
Answer: B
NEW QUESTION # 64
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 5 to 6 mils (125 to 150 microns)
- B. 6 to 7 mils (150 to 175 microns)
- C. 10 to 12 mils (250 to 300 microns)
- D. 8 to 10 mils (200 to 250 microns)
Answer: B
NEW QUESTION # 65
Prior to using Inspection Tools the inspector must:
- A. Ensure the instrument is within calibration parameters
- B. Read the manufactures' instructions
- C. Be trained on how to use the instrument
- D. a), b) & c)
Answer: D
NEW QUESTION # 66
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Advise the Contractor he can proceed
- C. Call your supervisor
- D. Advise the Contractor he cannot proceed
Answer: A
NEW QUESTION # 67
......
Pass NACE NACE-CIP1-001 Premium Files Test Engine pdf - Free Dumps Collection: https://exampasspdf.testkingit.com/NACE/latest-NACE-CIP1-001-exam-dumps.html